Wettability of two different artificial saliva substitutes on injection moulded heat polymerized acrylic resin and CAD-CAM acrylic resin: an in vitro study.

Auteurs-es

  • Quraish Lal M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune
  • Aamir Godil Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune
  • Mosin Shaikh M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune
  • Smita Musani Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune
  • Ramandeep Dugal Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune
  • Ajinkya Kirad Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DOI :

https://doi.org/10.5195/d3000.2023.184

Mots-clés :

wettability, artificial saliva substitute, CAD-CAM acrylic resin, injection moulded acrylic resin, contact angle, Mouth Kote, Wet mouth.

Résumé

Aim: The purpose of this in vitro study was to evaluate the wettability of two different artificial saliva substitutes on injection moulded heat-polymerized acrylic resin and CAD-CAM acrylic resin and to compare these properties with natural saliva and distilled water.

Materials and method: Forty heat polymerized (injection moulded) acrylic resin specimens and forty CAD-CAM acrylic resin specimens were fabricated with each specimen measuring 10x10x2mm. Four groups of liquids namely distilled water, Wet mouth™, Mouth Kote™ and human saliva were used. A contact angle goniometer was used to measure the contact angles. Two contact angle readings were obtained on the right side and on the left side of the test specimen. The observations were recorded and a mean of the two readings was calculated. The same procedure was repeated for all specimens (heat cure resin and CAD-CAM) with all the four test groups of liquids.

Results: Contact angle measurements were significantly higher in Wet mouth™ and Mouth Kote™ solution of heat cure resin group compared to the CAD-CAM group (p-value<0.05 for both). Mouth Kote™ had lower mean contact angle (62.63 ± 4.59) than Wet mouth™ (77.46 ± 9.16) on CAD/CAM denture base resin. Mouth Kote also had lower mean contact angle (70.80 ± 4.79) than Wet mouth™ (97.77 ± 7.79) on injection moulded denture base resin.

Conclusion: Mouth kote had better wettability than wet mouth on both CAD-CAM and injection moulded acrylic resin. Both the saliva substitutes had better wettability on CAD-CAM than on injection moulded acrylic resin.

Bibliographies de l'auteur-e

Quraish Lal, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

P.G. student

Aamir Godil, Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

MDS Prosthodontics

Mosin Shaikh, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

P.G. student

Smita Musani, Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

MDS Prosthodontics

Ramandeep Dugal, Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

MDS Prosthodontics

Ajinkya Kirad, Professor, M.A. Rangoonwala College of Dental Sciences and Research Centre, Pune

DEPARTMENT OF PROSTHODONTICS

MDS Prosthodontics

Références

Aydin AK, Terzioglu H, Ulubaram K, Hasirci N. Wetting properties of saliva substitutes on acrylic resin. Int J Prosthodont 1997;10:473-7.

Davies A, Finlay IG. Oral care in advanced disease. Oxford: Oxford University Press; 2005. p. 100-3.

van der ReijdenWA, Veerman ECI, Nieuw Amerongen AV. Treatment of oral dryness related complaints (xerostomia) in Sjögren’s syndrome. Ann Rheum Dis 1999;58:465-73.

Kilani BHZ, Retief DH, Guldag MV, Castleberry DJ, Fischer TE. Wettability of selected denture base materials. J Prosthet Dent 1984;52:288-91.

Park MS, Kim YK. Viscosity and wettability of carboxymethylcellulose (CMC) solution and artificial saliva. J Oral Med 2007;32:365-73.

Kilani BHZ, Retief DH, Guldag MV, Castleberry DJ, Fischer TE. Wettability of selected denture base materials. J Prosthet Dent 1984;52:288-91.

Jaiswal N, Patil PG, Gangurde A, Parkhedkar RD. Wettability of 3 different artificial saliva substitutes on heat-polymerized acrylic resin. The Journal of Prosthetic Dentistry. 2019 Mar 1;121(3):517-22.

Glickman TS. Glossary of meteorology. 2nd ed. American Meteorological Society (2000).

Lira AF, Consani RL, Mesquita MF, Nóbilo MA, Henriques GE. Effect of toothbrushing, chemical disinfection and thermocycling procedures on the surface microroughness of denture base acrylic resins. Gerodontology. 2012 Jun;29(2):e891-7.

Monsenego P, Baszkin AM, de Lourdes Costa M, Lejoyeux J. Complete denture retention. Part II: wettability studies on various acrylic resin denture base materials. J Prosthet Dent 1989;62:308-12.

Vissink A, De Jong HP, Busscher HJ, Arends JS, 's-Gravenmade EJ. Wetting properties of human saliva and saliva substitutes. Journal of dental research. 1986 Sep;65(9):1121-4.

Ramanna PK. Wettability of three denture base materials to human saliva, saliva substitute, and distilled water: A comparative in vitro study. J Indian Prosthodont Soc 2018;18:248-56.

Al‐Dwairi ZN, Tahboub KY, Baba NZ, Goodacre CJ, Özcan M. A comparison of the surface properties of CAD/CAM and conventional polymethylmethacrylate (PMMA). Journal of Prosthodontics. 2019 Apr;28(4):452-7.

Van der Reijden WA, Veerman EC, Nieuw Amerongen AV. Rheological properties of commercially available polysaccharides with potential use in saliva substitutes. Biorheology. 1994 Jan 1;31(6):631-42.

Téléchargements

Publié-e

2023-02-14

Numéro

Rubrique

Adults & the Elderly