Marginal Fit of Metal Copings Made by Three Fabrication Routes

Authors

  • Samah Khaleel Radhi Al-Gebori Department of dental technology, college of the health and medical technology ,university of hilla ,Iraq
  • Sajad Athab Hassan
  • Ahmed Hazim K. Al-Wtatfi

DOI:

https://doi.org/10.5195/d3000.2026.1135

Keywords:

Prosthodontics, Inlay, Onlay, Dental Crown

Abstract

Objective: The accuracy of marginal fit is essential for the longevity of metal restorations because any gap increases biological and mechanical risks. Digital fabrication methods, such as milling and 3D printing, were introduced to reduce the errors seen in conventional casting. This study compares the marginal gaps of copings made by the three techniques to identify the most accurate method within clinical limits. Materials and Methods: Thirty copings, ten per technique, were made on a standardized maxillary molar preparation. Vertical marginal gaps were measured at the buccal and lingual reference points under a stereo microscope at ×40 using image analysis software. Results: Mean marginal gap was 36.05 μm for printed Co-Cr, 45.15 μm for milled Ti, and 67.04 μm for cast Co-Cr. Differences were significant at p ≤ 0.05. Conclusion: 3D printing produced the smallest gaps, followed by milling, then casting. All means were within a commonly accepted clinical limit of 100 μm. Clinical significance, digital workflows can reduce inaccuracy and support restoration longevity.

Downloads

Published

2026-02-17

Issue

Vol. 14 No. 1 (2026): 2026

Section

Adults & the Elderly

License

Copyright (c) 2026 Samah Khaleel Radhi Al-Gebori, Sajad Athab Hassan, Ahmed Hazim K. Al-Wtatfi

Creative Commons License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Authors who publish with this journal agree to the following terms:

  1. The Author retains copyright in the Work, where the term “Work” shall include all digital objects that may result in subsequent electronic publication or distribution.
  2. Upon acceptance of the Work, the author shall grant to the Publisher the right of first publication of the Work.
  3. The Author shall grant to the Publisher and its agents the nonexclusive perpetual right and license to publish, archive, and make accessible the Work in whole or in part in all forms of media now or hereafter known under a Creative Commons Attribution 4.0 International License or its equivalent, which, for the avoidance of doubt, allows others to copy, distribute, and transmit the Work under the following conditions:
    1. Attribution—other users must attribute the Work in the manner specified by the author as indicated on the journal Web site;
    with the understanding that the above condition can be waived with permission from the Author and that where the Work or any of its elements is in the public domain under applicable law, that status is in no way affected by the license.
  4. The Author is able to enter into separate, additional contractual arrangements for the nonexclusive distribution of the journal's published version of the Work (e.g., post it to an institutional repository or publish it in a book), as long as there is provided in the document an acknowledgement of its initial publication in this journal.
  5. Authors are permitted and encouraged to post online a prepublication manuscript (but not the Publisher’s final formatted PDF version of the Work) in institutional repositories or on their Websites prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work. Any such posting made before acceptance and publication of the Work shall be updated upon publication to include a reference to the Publisher-assigned DOI (Digital Object Identifier) and a link to the online abstract for the final published Work in the Journal.
  6. Upon Publisher’s request, the Author agrees to furnish promptly to Publisher, at the Author’s own expense, written evidence of the permissions, licenses, and consents for use of third-party material included within the Work, except as determined by Publisher to be covered by the principles of Fair Use.
  7. The Author represents and warrants that:
    1. the Work is the Author’s original work;
    2. the Author has not transferred, and will not transfer, exclusive rights in the Work to any third party;
    3. the Work is not pending review or under consideration by another publisher;
    4. the Work has not previously been published;
    5. the Work contains no misrepresentation or infringement of the Work or property of other authors or third parties; and
    6. the Work contains no libel, invasion of privacy, or other unlawful matter.
  8. The Author agrees to indemnify and hold Publisher harmless from Author’s breach of the representations and warranties contained in Paragraph 6 above, as well as any claim or proceeding relating to Publisher’s use and publication of any content contained in the Work, including third-party content.

Revised 7/16/2018. Revision Description: Removed outdated link.